Audi A6 Owners & Service Manuals
Audi A6 Typ 4G (2011–2018) Owner's Manual / Maintenance and Care / Wheels / New tires or wheels

Audi A6 Typ 4G: New tires or wheels

Audi recommends having all work on tires or wheels performed by an authorized Audi dealer or authorized Audi Service Facility.

These facilities have the proper knowledge and are equipped with the required tools and replacement parts.

  • New tires do not yet have the optimum gripping properties.

    Drive carefully and at moderate speeds for the first 350 miles (500 km) with new tires.

  • Use tires of the same construction, size (rolling circumference) and as close to the same tread pattern as possible on all four wheels.
  • Do not replace tires individually.

    At least replace both tires on the same axle at the same time.

  • Audi recommends that you use Audi Original Tires. If you would like to use different tires, please note that the tires may perform differently even if the same size .
  • If you would like to equip your vehicle with a tire/rim combination that is different from what was installed at the factory, consult with an authorized Audi dealer or authorized Audi Service Facility before making a purchase .

The spare tire is different from the regular tires installed on the vehicle - for example, if winter tires or wide tires are installed - so only use the spare tire temporarily in case of emergency and drive carefully while it is in use. It should be replaced with a regular tire as soon as possible.

Applies to: vehicles with all wheel drive

All four wheels must be equipped with tires that are the same brand and have the same construction and tread pattern so that the drive system is not damaged by different tire speeds. For this reason, in case of emergency, only use a spare tire that is the same circumference as the regular tires.

WARNING

  • Only use tire/rim combinations and suitable wheel bolts that have been approved by Audi. Otherwise, damage to the vehicle and an accident could result.
  • For technical reasons, it is not possible to use tires from other vehicles - in some cases, you cannot even use tires from the same vehicle model.
  • Make sure that the tires you select have enough clearance to the vehicle. Replacement tires should not be chosen simply based on the nominal size, because tires with a different construction can differ greatly even if they are the same size. If there is not enough clearance, the tires or the vehicle can be damaged and this can reduce driving safety and increase the risk of an accident.
  • Only use tires that are more than six years old when absolutely necessary and drive carefully when doing so.
  • Do not use run-flat tires on your vehicle. Using them when not permitted can lead to vehicle damage or accidents.
  • If you install wheel covers on the vehicle, make sure they allow enough air circulation to cool the brake system. If they do not, this could increase the risk of an accident.

    READ NEXT:

     Tire wear/damage

    Fig. 189 Tire profile: treadwear indicator Tire wear Check the tires regularly for wear. Inflation pressure that is too low or high can increase tire wear considerably. Driving quickly through c

     Tire pressure

    Fig. 190 Driver's side B-pillar: tire pressure label Fig. 191 Tire pressure label The correct tire pressure for tires mounted in the factory and for the spare tire is indicated on a label. The labe

     Tires and vehicle load limits

    There are limits to the amount of load or weight that any vehicle and any tire can carry. A vehicle that is overloaded will not handle well and is more difficult to stop. Overloading can not only lea

    SEE MORE:

     Launch control program

    Applies to: vehicles with S tronic The launch control program provides the best possible acceleration when starting from a stop. Requirement: the engine must be at operating temperature and the steering wheel must not be turned. Deactivate the Start/Stop system. The LED in the button turns on.

     Rain/Light Recognition Sensor, Removing and Installing

    Rain/Light Recognition Sensor -G397-, Removing and Installing, without Humidity Sensor -G355- Special tools and workshop equipment required Cleaning Solution -D 009 401 04- Removing - Remove the interior rearview mirror. Refer to → Body Interior; Rep. Gr.68; Interior Rearv

    © 2011-2024 Copyright www.aa6.tochrfr.com