Audi A6 Owners & Service Manuals
Audi A6 Typ 4G (2011–2018) Owner's Manual / Maintenance and Care / Wheels / Tires and vehicle load limits

Audi A6 Typ 4G: Tires and vehicle load limits

There are limits to the amount of load or weight that any vehicle and any tire can carry. A vehicle that is overloaded will not handle well and is more difficult to stop.

Overloading can not only lead to loss of vehicle control, but can also damage important parts of the vehicle and can lead to sudden tire failure, including a blowout and sudden deflation that can cause the vehicle to crash.

Your safety and that of your passengers also depends on making sure that load limits are not exceeded.

Vehicle load includes everybody and everything in and on the vehicle. These load limits are technically referred to as the vehicle's Gross Vehicle Weight Rating ("GVWR").

The "GVWR'' includes the weight of the basic vehicle, all factory installed accessories, a full tank of fuel, oil, coolant and other fluids plus maximum load. The maximum load includes the number of passengers that the vehicle is intended to carry ("seating capacity") with an assumed weight of 150 lbs. (68 kg) for each passenger at a designated seating position and the total weight of any luggage in the vehicle. If you tow a trailer, the weight of the trailer hitch and the tongue weight of the loaded trailer must be included as part of the vehicle load.

The Gross Axle Weight Rating ("GAWR") is the maximum load that can be applied at each of the vehicle's two axles.

The fact that there is an upper limit to your vehicle's Gross Vehicle Weight Rating means that the total weight of whatever is being carried in the vehicle (including the weight of a trailer hitch and the tongue weight of the loaded trailer) is limited. The more passengers in the vehicle or passengers who are heavier than the standard weights assumed mean that less weight can be carried as luggage.

The Gross Vehicle Weight Rating and the Gross Axle Weight Rating are listed on the safety compliance sticker label located on the driver's side B-pillar fig. 190.

WARNING

Overloading a vehicle can cause loss of vehicle control, a crash or other accident, serious personal injury, and even death.

  • Carrying more weight than your vehicle was designed to carry w ill prevent the vehicle from handling properly and increase the risk of the loss of vehicle control.
  • The brakes on a vehicle that has been overloaded may not be able to stop the vehicle within a safe distance.
  • Tires on a vehicle that has been overloaded can fail suddenly, including a blowout and sudden deflation, causing loss of control and a crash.
  • Always make sure that the total load being transported - including the weight of a trailer hitch and the tongue weight of a loaded trailer - does not make the vehicle heavier than the vehicle's Gross Vehicle Weight Rating.

    READ NEXT:

     Determining correct load limit

    Use the example below to calculate the total weight of the passengers and luggage or other things that you plan to transport so that you can make sure that your vehicle will not be overloaded. Steps f

     Winter tires

    Winter tires significantly improve the vehicle's handling when driving in winter conditions. Because of their construction (width, compound, tread pattern), summer tires provide less traction on ice a

     Snow chains

    Snow chains not only improve the driving in winter road conditions, but also the braking. Only install snow chains on the front wheels. This applies also to vehicles with all wheel drive. Check a

    SEE MORE:

     Front Seat Belt Guide, Removing and Installing

    Front Seat Belt Guide, Removing and Installing Removing - Remove the upper B-pillar trim panel. Refer to → Chapter "Upper B-Pillar Trim, Removing and Installing". - Set aside the upper B-pillar trim with the seat belt still threaded through it. - Remove the lower B-pillar trim

     Hood Latch, Removing and Installing

    Removing - Disconnect the connector -4- from the anti-theft alarm system. - Disconnect the connector from the lock carrier. - Free up the release cable -1- by removing the clamps. - Remove bolts -3-. - Disconnect the hook from the cable -left arrow- and remove it with th

    © 2011-2024 Copyright www.aa6.tochrfr.com